Go Factory Direct — Source Your Batteries from Avepower.

Source LiFePO4 energy storage batteries directly from Avepower for resale, installation, OEM/ODM and project supply.

Start Your Request
Tell us your requirements and get a tailored quote.

How to Connect 4 12V Batteries in Series to Make 48V?

4 batteries in series

Battery systems are widely used in renewable energy, backup power, electric vehicles, marine applications, and off-grid power systems. Many of these systems require higher voltages than a single battery can provide.

If you have four 12-volt batteries and want to build a 48-volt battery bank, connecting them in series is the correct method. This configuration is commonly used in solar energy storage systems, UPS backup power, telecom equipment, and home energy storage solutions.

In this guide, we will explain how to connect 4 batteries in series, why series wiring increases voltage, what equipment you need, and the safety practices required to build a reliable 48V battery system.

What Does It Mean to Connect 4 Batteries in Series?

Connecting 4 batteries in series means joining the batteries in a chain so that the positive terminal of one battery connects to the negative terminal of the next battery. In a series connection, voltage adds up, while the amp-hour capacity stays the same as that of a single battery.

This setup is particularly advantageous for home energy storage or solar systems where higher voltage is required. Higher voltage systems are beneficial because they reduce the current needed for the same power output. Lower current reduces energy losses in cables, heat generation, and the required cable thickness, making the system more efficient and safer.

Example: 4 × 12V Battery Configuration

Each battery specification:

  • Voltage: 12V
  • Capacity: 100Ah
  • Energy: 1.2 kWh

Calculation: Energy = Voltage × Capacity

So: 12V × 100Ah = 1200Wh (1.2kWh)

For four batteries in series:

ParameterValue
Voltage48V
Capacity100Ah
Energy4.8kWh

The final system becomes: 48V 100Ah battery bank (4.8 kWh).

Note for LiFePO4 batteries: Four 12.8V 100Ah LiFePO4 batteries connected in series form a 51.2V 100Ah battery bank with a nominal energy capacity of 5.12kWh (51.2V × 100Ah ÷ 1,000). For four nominal 12V 100Ah lead-acid batteries, the nominal bank remains 48V 100Ah, or 4.8kWh. Actual usable energy depends on the battery chemistry, allowable depth of discharge, operating conditions, and system losses.

avepower lifep04 12v 100ah battery

Power That Lasts

If you want a battery you can just install and forget, go with an Avepower LiFePO4.
You get 4000+ cycles, around 10 years of use, a built-in BMS, and capacity you can expand later as your needs grow—just talk to Avepower for easy sizing advice and a no-pressure quote.

Why Use 4 12V Batteries to Make 48V?

There are several reasons why users choose 4 batteries in series instead of buying one single 48V battery.

1. Flexibility

Twelve-volt batteries are widely available and easy to source in most markets. By connecting four 12V batteries in series, users can conveniently build a 48V battery bank without needing specialized high-voltage battery modules.

2. Easy Replacement

If one battery fails, it may be possible to replace the faulty unit instead of replacing an entire high-voltage pack, although all replacement decisions must be made carefully to maintain balance.

3. Suitable for 48V Systems

Many inverters, solar charge controllers, telecom devices, and energy storage systems are designed around 48V architecture. A 48V system offers lower current than a 12V system for the same power level, which helps reduce cable size and energy loss.

4. Higher Efficiency

Higher voltage systems require less current to deliver the same power. Lower current helps reduce cable energy loss, minimize heat generation, and allows the use of thinner cables.

System VoltageCurrent Required for 3000W
12V250A
24V125A
48V62.5A

5. Practical for Solar and Backup Power

In off-grid and hybrid solar applications, 48V battery banks are often preferred because they are more efficient than lower-voltage battery setups, especially when powering larger loads.

How Series Wiring Works in Simple Terms

To understand series wiring, imagine the batteries as steps in a staircase. Each battery raises the voltage level by another 12V. When connected correctly, the electrical potential increases from one end of the battery bank to the other.

Here is the basic logic:

  • Start at the negative terminal of Battery 1
  • Connect the positive terminal of Battery 1 to the negative terminal of Battery 2
  • Connect the positive terminal of Battery 2 to the negative terminal of Battery 3
  • Connect the positive terminal of Battery 3 to the negative terminal of Battery 4
  • The remaining open terminals become the output:
    • System negative = negative terminal of Battery 1
    • System positive = positive terminal of Battery 4

At that point, the total voltage measured across the two free end terminals should be about 48V nominal.

In a fully charged state, the actual voltage may be higher than 48V depending on battery chemistry. For example, lead-acid and lithium batteries have different charging ranges and resting voltages. Still, the nominal system is called 48V because four 12V batteries are connected in series.

What You Need Before Connecting 4 Batteries in Series

Before starting, make sure the batteries are appropriate for series connection and that all components are compatible with a 48V system.

1. Four Identical 12V Batteries

All batteries in the series should be identical. They should have:

  • The same brand
  • The same capacity
  • The same battery chemistry
  • The same age and usage condition

Using mismatched batteries can lead to uneven charging and discharging, which may reduce system efficiency and shorten battery lifespan. In severe cases, it can also cause overheating or premature battery failure.

2. Battery Cables

For a 48V battery bank, cable size must be selected based on the maximum DC current, total cable length, allowable voltage drop, cable ampacity, and installation conditions. A cable cannot be safely sized by current alone.

For example, a 3,000W inverter operating at 48V with an assumed 90% efficiency draws approximately 69.4A from the battery. A 5,000W inverter under the same conditions draws approximately 115.7A. The actual current may be higher at lower battery voltages or during inverter surge conditions.

How Much Current Does a 48V Inverter Draw?

The approximate DC input current is calculated as:

DC Current (A) = AC Output Power (W) ÷ [Battery Voltage (V) × Inverter Efficiency]

Inverter OutputBattery VoltageAssumed EfficiencyEstimated DC Current
1,000W48V90%23.1A
2,000W48V90%46.3A
3,000W48V90%69.4A
5,000W48V90%115.7A
6,000W48V90%138.9A

48V Battery Cable Size Reference

Copper Cable Cross-SectionReference Current at 5m Total Cable Length
10 mm²30A
16 mm²48A
25 mm²75A
35 mm²105A
50 mm²150A
70 mm²210A

For a 3,000W inverter drawing approximately 69.4A at the stated reference voltage, 25 mm² copper cable meets its approximately 0.259V voltage-drop reference for a total circuit length of up to 5 meters. This does not establish that 25 mm² cable is suitable for every 3,000W inverter installation.

Before selecting the final cable size:

  1. Calculate maximum current: Use the inverter’s maximum specified DC input current, including the effects of low battery voltage and any relevant surge conditions.
  2. Measure cable length: Include the complete positive and negative current path. Check series interconnects for the current they must carry.
  3. Check voltage drop: Avepower recommends aiming for less than 2.5% voltage drop across the DC cabling, subject to equipment requirements.
  4. Verify cable ampacity: Check conductor material, insulation temperature rating, ambient temperature, routing, bundling, and the applicable electrical installation rules.
  5. Coordinate protection: Select a properly rated DC fuse or circuit breaker based on the cable’s allowable current, battery/BMS limits, equipment requirements, and available fault current. The protection device must have an adequate DC interrupt rating.
  6. Inspect connections: Use compatible cable lugs and terminals, correct crimping methods, and the manufacturer’s specified tightening torque.

For LiFePO4 batteries connected in series, verify that the battery manufacturer permits four batteries in series and that the BMS configuration supports the complete system. All four batteries carry the same series current, so the bank’s current capability does not increase by connecting the batteries in series.

Cable sizing and protection should be verified by a qualified installer before commissioning a high-current battery system.

Avepower home energy storage battery

Take Control of Your Energy with Avepower!

Reliable home solar battery solutions with OEM/ODM customization and in-house manufacturing, tailored to the needs of distributors, installers, and energy partners.

3. Battery Terminals or Busbars

Battery terminals or busbars are used to create secure and stable connections between batteries. Proper connectors ensure low resistance and prevent loose contacts that could lead to overheating.

4. Fuse or Circuit Breaker

A fuse or circuit breaker is essential for system protection. It helps prevent damage caused by:

  • Short circuits
  • Overcurrent conditions
  • Wiring faults

Installing a fuse near the battery bank is a common safety practice in battery systems.

5. Insulated Tools

Always use insulated tools when working with batteries. This helps prevent accidental short circuits and reduces the risk of electric shock or equipment damage during installation.

how to connect 4 12v batteries in series to make 48v

Step-by-Step: How to Connect 4 12V Batteries in Series to Make 48V

Step 1: Place the Batteries in Position

Arrange the four 12V batteries close enough that the interconnect cables can reach comfortably, but not so tightly packed that heat dissipation becomes a problem.

Label them mentally or physically as:

  • Battery 1
  • Battery 2
  • Battery 3
  • Battery 4

Keeping the layout organized helps avoid polarity mistakes.

Step 2: Verify Battery Voltage

Before making any connections, use a multimeter to check the voltage of each battery.

For example, if they are nominal 12V batteries, each one may read:

  • Around 12.6V to 12.8V if fully charged lead-acid
  • Around 13.2V to 13.6V for some lithium 12V batteries depending on chemistry and state of charge

The key point is not the exact reading, but that all four batteries should be very close in voltage. Large differences indicate unequal charge levels and may cause stress after connection.

Step 3: Connect Battery 1 Positive to Battery 2 Negative

Take the first interconnect cable and connect:

  • Battery 1 positive (+) to Battery 2 negative (-)

Tighten the terminals to the manufacturer’s torque recommendation. Do not overtighten.

Step 4: Connect Battery 2 Positive to Battery 3 Negative

Take the second interconnect cable and connect:

  • Battery 2 positive (+) to Battery 3 negative (-)

At this stage, the chain continues to build voltage.

Step 5: Connect Battery 3 Positive to Battery 4 Negative

Take the third interconnect cable and connect:

  • Battery 3 positive (+) to Battery 4 negative (-)

Now the four batteries are linked in series.

Step 6: Identify the Main Output Terminals

At the end of the chain, two free terminals remain:

  • Battery 1 negative (-) becomes the main negative output
  • Battery 4 positive (+) becomes the main positive output

These are the only two terminals you use to connect the battery bank to a 48V inverter, charger, controller, or load.

Step 7: Measure the Total Voltage

Use a multimeter across the two free end terminals:

  • Black probe on Battery 1 negative
  • Red probe on Battery 4 positive

You should measure approximately 48V nominal.

Depending on battery chemistry and charge level, the reading might be:

  • Around 50V to 54V in some resting or partially charged states
  • Higher during charging
  • Lower when discharged

But if the reading is close to zero, 12V, 24V, or 36V, the wiring is incorrect and should be checked before connecting any equipment.

Simple Wiring Diagram for 4 Batteries in Series

Here is a basic text diagram:

System Negative
(-) Battery 1 (+) — (-) Battery 2 (+) — (-) Battery 3 (+) — (-) Battery 4 (+)
System Positive

Or more explicitly:

  • Battery 1 negative = system negative
  • Battery 1 positive to Battery 2 negative
  • Battery 2 positive to Battery 3 negative
  • Battery 3 positive to Battery 4 negative
  • Battery 4 positive = system positive

That is the standard arrangement for 4 batteries in series.

Charging a 48V Battery Bank

A 48V battery bank made from four 12V batteries in series requires a charger compatible with the complete battery bank and its chemistry. For four 12.8V LiFePO4 batteries, the nominal voltage is 51.2V, while the correct charging voltage depends on the battery manufacturer’s specifications.

48V Battery Charging Voltage by Battery Type

Battery ConfigurationNominal Bank VoltageCharging Voltage Example
4 × 12.8V LiFePO451.2V56.8V absorption
4 × 12.8V LiFePO451.2V57.6V charging
4 × 12V AGM lead-acid48V57.6V absorption
4 × 12V Gel lead-acid48V56.8V absorption

Why Do 48V LiFePO4 Batteries Have a 51.2V Nominal Voltage?

A typical LiFePO4 cell has a nominal voltage of 3.2V. A 12.8V LiFePO4 battery contains four such cells in series.

Connecting four compatible 12.8V batteries in series produces:

12.8V × 4 = 51.2V nominal

This is commonly described as a 48V-class lithium battery system, even though its actual nominal voltage is 51.2V.

How Much Charging Current Can Four Batteries in Series Handle?

Connecting four batteries in series increases the voltage, but it does not multiply the allowable charging current.

For example, if each compatible 12.8V 100Ah battery has a manufacturer-approved maximum charging current of 50A, four batteries connected in series still have a 50A maximum charging current, not 200A.

The charging current must remain within the most restrictive limit of the battery modules, BMS, wiring, charger, and other system components.

Before Charging Four Batteries in Series

Confirm that:

  • The battery manufacturer explicitly approves four batteries in series.
  • The batteries have compatible chemistry, capacity, model, and condition.
  • Each battery has been charged and balanced according to the manufacturer’s instructions before series connection.
  • The charger supports the required battery-bank voltage and charging profile.
  • The BMS can monitor and protect the complete series configuration, including overvoltage, undervoltage, temperature, and charging restrictions.
  • The charge current, absorption voltage, float behavior, and any equalization settings match the exact battery specifications.

Do not use a generic 48V lead-acid charging profile for LiFePO4 batteries unless the battery manufacturer explicitly approves those settings. Incorrect charging voltage, inadequate balancing, or unsupported series connections can cause the BMS to disconnect the system and may damage the batteries.

How to Check If the Connection Is Correct

After wiring the batteries, you should verify the voltage before connecting any inverter, charger, or load.

Use a Multimeter

Set the multimeter to measure DC voltage.

Place:

  • The black probe on Battery A negative
  • The red probe on Battery D positive

If the batteries are healthy and properly charged, you should measure approximately 48V nominal, though the real reading may vary depending on battery chemistry and state of charge.

For example:

  • Around 50–54V may be seen in some charged lead-acid systems
  • Around 51–53.6V or more may be seen in lithium systems depending on charging level and chemistry

The key point is that the voltage should be roughly the combined total of the four 12V batteries.

Also Check Each Battery Individually

Measure each battery one by one:

  • Battery A
  • Battery B
  • Battery C
  • Battery D

They should all be close in voltage. A large difference may indicate a weak battery, poor connection, or uneven charge level.

4 Batteries in Series vs Parallel

  • Series connection increases voltage
  • Parallel connection increases amp-hour capacity (Ah)

So when people say 4 batteries in series and parallel, they often mean arranging four batteries into a mixed configuration, not all in one straight series string and not all in one parallel group.

Number of BatteriesWiring MethodSingle Battery RatingConnection TypeFinal Output
4Connect all 4 batteries end to end12V 100AhSeries48V 100Ah
4Connect all positive terminals together and all negative terminals together12V 100AhParallel12V 400Ah
4Connect 2 batteries in series per string, then connect the 2 strings in parallel12V 100AhSeries-Parallel24V 200Ah

Related articles: 4 batteries in parallel

When a 48V System Makes More Sense Than 12V or 24V

Many small systems start at 12V because it is simple and familiar. But as system size increases, 48V becomes more attractive.

A 48V battery bank built from 4 batteries in series is usually a better choice when:

  • Load power is moderate to high
  • Cable runs are longer
  • Inverter size is 3000W or above
  • Efficiency matters
  • Heat and current need to be reduced
  • The system is part of a solar storage application

In short, 48V systems are often the next step when a project grows beyond the practical limits of 12V.

Need a Higher-Voltage Energy Storage Solution?

If you need a higher-voltage battery system for residential ESS, commercial backup, or solar storage projects, choosing the right battery configuration is critical for safety, efficiency, and long-term performance. Avepower offers professional high-voltage energy storage solutions with reliable LiFePO4 technology, and flexible system customization to match different application needs.

Avepower has already supported a 522.496kWh high-voltage ESS project in Lithuania, built around a nominal 832V DC architecture for commercial and industrial grid support and renewable integration. The system was configured as a compact four-cabinet solution, with two clusters connected in parallel, demonstrating strong capability in high-voltage system design, integration, and delivery.

522.5kwh high-voltage battery

High-Voltage Energy Storage Solutions with Avepower

Contact Avepower today to discuss your voltage range, target capacity, and project requirements.

FAQ

How do you connect 4 batteries in series to make 48V?

To connect 4 batteries in series and make 48V, connect the positive terminal of the first 12V battery to the negative terminal of the second, then continue the same pattern across all four batteries. The remaining free negative terminal on the first battery and the free positive terminal on the fourth battery become the 48V output terminals.

What voltage do 4 batteries in series produce?

If you use four 12V batteries, the total nominal voltage will be: 12V + 12V + 12V + 12V = 48V. So, 4 batteries in series produce 48V, provided all batteries are correctly connected and in good condition.

Does capacity increase when 4 batteries are connected in series?

No. When 4 batteries are connected in series, the voltage increases, but the amp-hour capacity stays the same as one battery.

What size battery bank do I get from 4 x 12V 100Ah batteries in series?

If you connect 4 x 12V 100Ah batteries in series, you get a 48V 100Ah battery bank.

Can I charge 4 batteries in series with a 12V charger?

No. A battery bank made from 4 batteries in series becomes a 48V system, so it requires a 48V charger that matches the battery chemistry. A 12V charger is not suitable for charging a 48V battery bank.

Can I take 12V power from one battery in a 48V series bank?

Pulling 12V power from one battery in a 4 batteries in series bank can cause uneven discharge and battery imbalance. Over time, this may damage the battery bank and reduce overall lifespan.

What size cable do I need for four 12V batteries in series?

There is no single cable size suitable for every 48V battery bank. A 3,000W inverter draws approximately 69.4A at 48V with 90% efficiency.

What voltage should I use to charge four 12V LiFePO4 batteries in series?

Four 12.8V LiFePO4 batteries in series have a nominal voltage of 51.2V.

Picture of Ryan

Ryan

Ryan is an energy expert with over 10 years of experience in the field of battery energy storage and renewable solutions. He is passionate about developing efficient, safe, and sustainable battery systems. In his spare time, he enjoys adventure and exploring.

Learn more about Ryan
Share on social:

Leave a Comment

Your email address will not be published. Required fields are marked *

lifepo4 home solar battery for wholesale

About Avepower

Backed by 10+ years of battery manufacturing experience and a 20,000㎡ factory, Avepower delivers reliable LiFePO4 energy storage solutions worldwide.

Send Your Requirements

Get battery type, capacity, and solution suggestions in one quick form.

Get Expert Battery Selection Support

For Distributors

Avepower supply quality products with stable support to grow your business.

For Wholesalers

Get bulk supply, competitive pricing, and reliable product availability.

For Installers

Easy-to-install systems with strong performance and full support.

Energy Storage Solution Quote

Battery Quote Request

Get a Quote & Download Catalog

Custom Energy Storage Solutions

OEM & ODM services designed for installers, wholesalers, distributors, and global brands.

avepower energy storage battery system manufacturing factory (1)

Get Avepower Catalog

Full energy storage specs and details in one PDF. Enter your email and we’ll send it to you.

Get Battery Quote & Solution